Ontario: University of Windsor, 2017. — 15 s. Research Objectives and Scope System Configuration Safety Precautions University of Windsor ASHRAE Project Video
New York: Mechanical Technology Incorporated, 1982. — 468 p. In the internal combustion engine power output is primarily controlled by the intake throttle valve position which specifies the cylinder mass air charge. The Stirling engine cannot become self-sustaining and deliver shaft output until the heater tubes have been heated by the ester combustion. Before the vehicle can...
Thesis Prepared for the Degree of Master of Science. — Denton: University of North Texas, 2015. — 64 p. Stirling engines are an external combustion heat engine that converts thermal energy into mechanical work that a closed cycle is run by cyclic compression and expansion of a work fluid (commonly air or Helium) in which, the working fluid interacts with a heat source and a heat...
In partial fulfillment of the requirements for the Degree of Bachelor of Science. — Worcester, Polytechnic Institute, 2016. — 69 p. A Stirling engine is an external combustion engine that creates work by utilizing a temperature gradient within a cylinder to drive a piston. These engines are attractive options for green technologies because the temperature differential can be...
A thesis submitted for the Degree of Doctor of Philosophy in Mechanical Engineering at the University of Canterbury. — Christchurch, New Zealand, University of Canterbury, 1993. — 316 p. The benefits of the Stirling Cycle have been known for well over a century but several specific problems have prevented its common use in modern society. During 1989 this PhD project was...
Crowood Press, 2005. — 250 p. — ISBN 186126688. Great guide for building and designing your own thermal engines. Hot air engines, often called Stirling engines, are among the most interesting and intriguing engines ever to be designed. They run on just about any fuel, from salad oil and hydrogen to solar and geothermal energy. They produce a rotary motion that can be used to...
Springer Science+Business Media Singapore, 2016. – 242 p. – ISBN10: 981100322X. This monograph focuses on the dynamical research work on crank-piston mechanisms considering basic and additional motions. In order to have full dynamical analyses of piston machines and their mechanisms, the book studies the crank-piston mechanisms with clearances in kinematic pairs. The tasks are...
Prepared for the Second International Energy Conversion Engineering Conference sponsored by the American Institute of Aeronautics and Astronautics Providence, Rhode Island, August 16–19, 2004. 28 p. Nuclear thermal to electric power conversion carries the promise of longer duration missions and higher scientist data transmission rates back to Earth for a range of missions,...
American Society of Mechanical Engineers (ASME), 2001. 268 p. — ISBN 0791801713. Dedication Foreword Notation Air engines Classification The regenerator Furnace gas engines Ericsson engines The Stirling engine The invention Working principle The patent Degenerate Stirling engines – double-cylinder types Later single cylinder engines German air engines Heinrici, Bailey, and...
Michigan: Village Press Inc, 2000. — 160 p. — ISBN 0-914104-06-3. At no time in history has participation in metal-working as a hobby grown as fast in America as it has in the past fifteen years. It is a safe assumption that as many metal-turning lathes have been purchased in the past five years for home workshops as were in such use prior to that time. Because of that growth,...
First Printing. — Michigan: Home Shop Machinist, 1994. — 240 p. OCR. — ISBN: 0-941653-18-8 Book two features eighteen steam engines and four Stirling hot air engines you cand build, plus boiler work and related topics.
Thesis to obtain the Master of Science Degree in Energy Engineering and Management. — Lisboa: IJT, 2014. — 73 p. This master thesis report presents the work performed on recovery of low grade heat into electricity using two different technologies. The two technologies studied are the Stirling engine and the Organic Rankine Cycle (ORC). The Stirling engine is studied for...
A thesis submitted in partial fulfilment of the requirements for the Degree of Doctor of Philosophy in Electrical Engineering. — Canterbury, University of Canterbury, 2012 — 229 p. Micro Combined Heat and Power systems or microCHP systems generate heat and electricity for a home. Stirling engines are widely used as prime movers in microCHP applications. Stirling engine is an...
A dissertation submitted in partial satisfaction of the requirements for the degree of Doctor of Philosophy in Engineering Electrical Engineering and Computer Sciences and the Designated Emphasis in Energy Science and Technology. — Berkeley: Graduate Division of the University of California, 2016. — 111 p. Addressing the challenge of climate change requires the large-scale...
Отчёт о результатах тестов электрогенератора на основе двигателя Стирлинга ( Ground Power Unit - GPU-3 ) на 6кВт, разработанного General Motors Research Laboratory для армии США.
Springer, 2016. — XIII, 143 p. — ISBN: 978-3-319-28354-8; ISBN: 978-3-319-28355-5 (eBook). Presents a novel idea for designing efficient heat air enginesReports on a theoretical study to improve heat exchange in externally heated valve engines Compares externally heated valve engines to Stirling engines This book reports on a novel approach for generating mechanical energy from...
Renewable and Sustainable Energy Reviews, 2003 (7), pp. 131–154 This article provides a literature review on solar-powered Stirling engines and low tempera- ture differential Stirling engines technology. A number of research works on the development of Stirling engines, solar-powered Stirling engines, and low temperature differential Stirling engines is discussed. The aim of...
2005, 15 p. Advisor: Professor E. Carr Everbach The goal of this project is to design, build and instrument a Solar Stirling-engine Water Pump using fluidyne technology and to evaluate its performance. The motivation behind the project is the recently revived interest in the liquid-piston Stirling engines as an alternative power source. The objectives of the project will be to...
A thesis submitted in partial fulfilment of the requirements for the Degree of Master of Engineering. — Canterbury, University of Canterbury, 2009. — 132 p. В диссертации приведены расчёты и частичная реализация двигателя Стирлинга с планируемой выходной мощностью 500 Вт при разности температур 60 С (в интервале температур от 30 С до 90 С). Рабочее тело - воздух, давление - 1...
Dearborn: Conservation and Solar Energy Office of Transportation Programs, 1980. — 24 p. A four working space, double acting piston, Stirling engine simulation was developed for controls studies. Two simulations, one for detailed fluid behavior, and a second model with simple fluid behavior but containing the four working space aspects and engine inertias, validate these models...
University of Gävle, 2007. — 33 p. Maier Christoph, Gil Arnaud, Aguilera Rafael, Shuang Li, Yu Xue. This essay mainly makes an exposition of the Stirling Engine. Firstly, the history of Stirling Engine is showed to make a guide of first comprehension. Then the Stirling Engine’s thermodynamic cycle is explained and the configuration is analyzed, which we do to make sure a...
Final Report (Joint center for graduate study). University of Washington; prepared for NASA Lewis Research Center; U.S. Department of Energy. April 1978. 370 p. На англ. языке. Цель данной работы - дать введение в тему тепловых машин Стирлинга, систематизировать литературу о двигателях Стирлинга (ДС), изучить и сопоставить известные методологии их проектирования. Содержание:...
A dissertation submitted of the degree of Doctor of Philosophy in Engineering - Electrical Engineering and Computer Sciences. University of Califonia, Berkeley, 2007. 207 p. Диссертация, представленная в университете Беркли ( UNIVERSITY OF CALIFORNIA, Berkeley ). Подробно описываются методы расчёта, этапы создания и параметры тестового образца компактного электрогенератора на...
Submitted to the department of Mechanical engineering in partial fulfillment of the requirements for the degree of Bachelor of Science in Mechanical Engineering. — Massachusetts, Institute of Technology, 1996. — 121 p. 2. 670: ME Tools was created during the revisions of the undergraduate curriculum in 1995. The development of 2.670 started in June 1995. It was first taught during...
Bachelor's thesis Automation Engineering, 2012. — 51 p. This study strives to provide a clear explanation of the Stirling engine and its efficiency using new automation technology and the Lab View software. This heat engine was invented by Stirling, a Scottish in 1918. The engine’s working principles are based on the laws of thermodynamics and ability of volume expansion of...
Latham-New York, Mechanical Technology Incorporated, 1986.— 54 p. Automotive stirling engine Engine design summary Mod II Stirling engine -a synopsis External heat system Hot engine system Cold engine/drive system Control systems and auxiliaries Conclusions Chevrolet celebrity specificxion Mod II engine specification Fuel economy and performance Calculations The automotive...
Alexandria: Institute for Defense Analyses, 1988. — 89 p. Обзор преимуществ двигателя Стирлинга и возможные варианты его использования в военном деле. This pape reports on the potential military applications of the Sfitiin engine. In the appliations considered here, the major advantages dited for the Stirling engine are ultifuel capability, efficiency, and low noise levels....
John Wiley & Sons, Ltd., 2014. XXII, 272 p. — ISBN: 9781118818435. Some 200 years after the original invention, internal design of a Stirling engine has come to be considered a specialist task, calling for extensive experience and for access to sophisticated computer modelling. The low parts-count of the type is negated by the complexity of the gas processes by which heat is...
CRC Press, 2007. 306 p. — ISBN-10:1845692314. Two centuries after its original invention, the Stirling engine has finally emerged as a commercial reality. Providing an alternative to centralized power generation, the Stirling is now employed as the core component in domestic CHP (combined heat and power) technology, which offers substantial savings in raw energy utilization and...
3rd edition. — Ross Expermental, 2011. — 68 p. The legendary Andy Ross book on Stirling engines, in both English. Photos, diagrams and detailed descriptions of several working models. Imagine a small engine for your bicycle, canoe, or campside generator that is as quiet as a sewing machine. Its exhaust flue gases are nonpoisonous, nonpolluting and practically odorless. It...
Cambridge University Press, 2007. 192 p. ISBN: 0521868807 This book presents a newly developed general conceptual and basic quantitative analysis of the mechanical efficiency of heat engines. The book works out the theory at a level of ideality and generality compatible with the treatment given to thermal efficiency by classical thermodynamics. This yields results of broad...
New York: The Stirling Co, 1905. — 248 p. Shortly after the invention of tlie doubleacting steam engine by Watt, the development of the water- tube boiler began, but of the many designs which appeared during the succeeding half century none proved successful. Yet not all of the ideas underlying these early and crude designs were valueless, and after a long course of...
Б.и. - 2011. - 96 с. History The Stirling Cycle The Basic Stirling Engine Parts Of A Stirling Engine Types Of Stirling Engines Stirling Cyrocoolers Performance Of Stirling Engines Application Of Stirling Engines How To Make A Stirling Engine Model How Do I Make A Real Stirling Engine? Suggested Further Refference
Oxford University Press, 1980. XXII, 532 p. — ISBN: 0-19-856209-8. Robert Stirling and His Family Ideal Thermodynamic Cycles Practical Regenerative Cycle Theoretical Analysis of Stirling Engines Preliminary Engine Design Mechanical Arrangements Heat Exchangers in Stirling Engines Working Fluids in Stirling Engines Operating Characteristics of Stirling Engines Control Systems...
1st edition. - Springer-Verlag Berlin, Heidelberg, 1985. XIV, 268 p. — ISBN13: 978-3-540-15495-2, DOl: 10.1007/978-3-642-82526-2, e-ISBN13: 978-3-642-82526-2 — (Lecture Notes in Engineering 12). List of Contents Introduction (G. Walker) Definition and Nomenclature History Thermodynamics of the Stirling Cycle The Stirling Cycle Refrigerator The Stirling Cycle Heat Pump The...
Svenskt Gastekniskt Center, 2004. — 44 p. This project has been initiated in order to develop a new type of natural gas fired low emission combustion system for a Stirling engine CHP-unit, and to demonstrate and evaluate the unit with the newly developed combustion system in a CHP application. The Stirling engine technology is well developed, but mostly used in special...
(Место и год опубликования неизвестны. ) 6 p. На англ. языке.
Предложена математическая модель цикла двигателя Стирлинга, в которой используются политропные процессы. Результат моделирования по этому методу сопоставлен с результатом моделирования по Г. Шмидту для двигателя TEDOM V180, описанного в диссертации автора.
Учебное пособие. — Самара: СГАУ, 2015. — 76 с.: ил. Приведены подробные теоретические сведения об основных принципах работы двигателя и холодильной машины Стирлинга. Описаны основные термодинамические процессы, происходящие при работе двигателя и холодильной машины Стирлинга. Приведены основные методики расчёта устройств, работающих по прямому и обратному циклу Стирлинга....
Иллюстративный материал к учебному курсу «Энергетические машины и установки». — МГТУ им.Н.Э. Баумана, Чирский С.П., 2015. — 13 слайдов.
Термодинамический цикл двигателя Стирлинга
Схемы двигателя Стирлинга
Модели двигателя Стирлинга
Конструкция и принцип действия двигателя Стирлинга
БГТУ, Брянск 2012. — 28 с.
Двигатель наружного сгорания (ДНС)
Производство двигателя Стирлинга новая отрасль в машиностроении XXI века
Рабочие характеристики и особенности конструкции
Очерк развития двигателей Стирлинга
Перспективы развития стирлингостроения в России
Новосибирск, 2013 г., разработчик Павлов Ю.В., сборочные чертежи: корпус в сборе, вытеснитель в сборе, шток, вытеснитель, регенератор, детали штока, регенератора, вытеснителя
Новосибирск, 2013 год, Павлов Ю.В., добавлены чертежи сборочных единиц: охладителя, вытеснителя, нагревателя, коленвала, шатуна и поршня; сборочный чертёж со спецификацией
Г. Новосибирск, 2013 г., Ю. Павлов, здесь таблицы Excel со всеми необходимыми расчётами по двигателю Стирлинга, ещё перечень материалов и стоимость изготовления деталей и узлов двигателя ДСТ 02 (прототип ДСТ 03)
Г. Новосибирск, 2013 г., Ю. Павлов, здесь я выложил программу Tdms и дополнительные файлы: чертежей и текстовый файл по регенератору. Все пояснения есть в текстовых файлах, также на поле некоторых чертежей
Учебное пособие. — Самара: Самарский национальный исследовательский университет им. академика С.П. Королева, 2020. — 112 с. — ISBN: 978-5-7883-1519-5. Изложены основные этапы расчета параметров двигателя с внешним подводом теплоты со свободным поршнем. Приведены особенности чис-ленного моделирования рабочего процесса в двигателе с учетом гидравлических потерь в теплообменниках...
М.: Машиностроение, 1977. — 150 с. На обороте тит. л. авт.: В. Н. Даниличев, С. И. Ефимов, В. А. Звонов и др. Книга знакомит читателя с поршневыми двигателями, имеющими внешний подвод теплоты – двигателями Стирлинга. В ней приведены сведения из теории рабочего процесса этих двигателей, рассмотрены их кинематика, динамика и характеристики. Описаны некоторые конструкции...
М.: Машиностроение, 1977. 150 с. На обороте тит. л. авт.: В. Н. Даниличев, С. И. Ефимов, В. А. Звонов и др. Книга знакомит читателя с поршневыми двигателями, имеющими внешний подвод теплоты – двигателями Стирлинга. В ней приведены сведения из теории рабочего процесса этих двигателей, рассмотрены их кинематика, динамика и характеристики. Описаны некоторые конструкции двигателей...
Пер. с англ. — М.: Мир, 1986. — 464 с., ил. В книге английских авторов дается обзор конструкций двигателей с внешним нагревом, работающих по замкнутому циклу (циклу Стирлинга), анализируются их рабочие характеристики. Излагаются основные вопросы теории, методы расчета и принципы конструирования таких двигателей. Рассматриваются перспективы их использования в различных областях....
Пер. с англ. — М.: Мир, 1986. — 464 с., ил. В книге английских авторов дается обзор конструкций двигателей с внешним нагревом, работающих по замкнутому циклу(циклу Стирлинга), анализируются их рабочие характеристики. Для специалистов в области проектирования, производства и использования тепловых двигателей, а также преподавателей и студентов технических вузов.
Статья опубликована в трудах III Международного конгресса по управлению отходами «ВэйстТэк-2003», Москва, 3-6 июня 2003 г. 30 с.
Рассмотрен ряд существенных моментов разработки упрощённого двигателя Стирлинга – выбор величины индикаторного КПД и оценка основных параметров упрощённых нагревателя и охладителя рабочего газа, а также регенератора. Показано, что при гладких...
Статья. Опубликовано в журнале: Двигателестроение, 2002, № 1, с. 9-12.
Рассматриваются проблемы двигателей Стирлинга, обсуждавшиеся в публикациях последних лет. Выделены проблемы определения рациональных областей применения двигателей, применения нетрадиционных топлив и нетрадиционных источников теплоты, уменьшения числа публикаций, содержащих научно-техническую информацию,...
Статья. Опубликовано в журнале: Двигателестроение, 2002, № 2, с. 3-6.
Рассматриваются кинематические механизмы и проблемы компоновки двигателей Стирлинга, обсуждавшиеся в публикациях последних лет. Приведены сведения о двигателях KS15D (DaimlerBenz), Mod III (MTI Inc.), WG3000 (Whisper Tech Ltd). Выделены проблемы повышения механического КПД и выбора кинематической схемы для...
Статья. Опубликована в журнале: Двигателестроение, 2002, № 3, с. 15-18.
Рассматриваются мероприятия, предпринимаемые для повышения КПД внешнего нагревательного контура двигателей Стирлинга, обсуждавшиеся в публикациях последних лет. Выделена проблема применения систем передачи теплоты к нагревателю двигателя на базе тепловой трубы с жидкометаллическим теплоносителем. Приведены...
Статья опубликована в Трудах 9-ой международной научно-практической конференции «Освоение минеральных ресурсов Севера: проблемы и решения», 6-8 апреля 2011 г./ Филиал СПГГИ (ТУ) «Воркутинский горный институт». – Воркута, 2011. – 745 с., с. 424-428.
Приводятся сведения об одноцилиндровом двигателе Стирлинга мощностью 2 кВт, предназначенного для работы на древесном топливе.
Статья. Опубликована в журнале: Двигателестроение, 2004, № 1, с. 15-17.
Рассматривается проблема регулирования двигателя Стирлинга методом изменения объема внутреннего контура. Приведены соотношения для оценки величины гидравлической потери на перетечку рабочего тела. Выполнены расчетные сопоставления мощности и эффективности на долевых режимах для двигателей различного типа....
Статья. Естественные и технические науки, 2010, № 6 (50), с. 402-407. Приведены результаты научных исследований и опытно-конструкторских работ по созданию двигателя Стирлинга для автономной многотопливной когенерационной установки. Сформулированы основные принципы двигателя для коммерческого применения на рынке малой энергетики.
Статья. Естественные и технические науки, 2010, № 6 (50), с. 408-411. Приведены результаты работ методами исследовательского проектирования по созданию охладителя двигателя Стирлинга, предназначенного для работы в составе автономной многотопливной когенерационной установки. Для выравнивания температурного поля в зоне поршневых колец и фланцевых соединениях обосновано введение в...
Статья опубликована в Трудах 9-ой международной научно-практической конференции «Освоение минеральных ресурсов Севера: проблемы и решения», 6-8 апреля 2011 г./ Филиал СПГГИ (ТУ) «Воркутинский горный институт». – Воркута, 2011. – 745 с., с. С. 429-432.
Приводятся сведения о конструкции и параметрах нагревателя. регенератора и охладителя двигателя Стирлинга мощностью 2 кВт, в...
Новосибирск, 2014, разработчик Павлов Ю., трёхмерная модель двигателя Стирлинга в Inventor Prof 2015 (iam, ipt), а также в форматах: step, stl, sat, parasolid x_b, pro/engineer
Монография. — Ташкент: Фан, 1979. — 80 с. Монография содержит анализ современного уровня разработок по двигателю Стирлинга, технико-экономическую оценку перспектив его использования в различных областях техники, в частности в солнечных энергоустановках, термодинамический анализ двигателя. Рассматриваются инженерные методы расчета и оптимизации теплообменников с учетом тепловых...
М.: Машиностроение, 1985. — 408 с. — (OCR). Сокр. Пер. с англ. Б.В. Сутугина и Н.В. Сутугина (Walker G. Stirling Engines / Clarendon Press, Oxford, 1980.) В книге изложены теория, расчет и конструирование двигателей различных модификаций, работающих по циклу Стирлинга. Описаны рабочие тела, системы регулирования, испытания и применения двигателей Стирлинга, даны их...
М.: Машиностроение, 1985. — 408 с. Сокр. Пер. с англ. Б.В. Сутугина и Н.В. Сутугина (Walker G. Stirling Engines / Clarendon Press, Oxford, 1980.) В книге изложены теория, расчет и конструирование двигателей различных модификаций, работающих по циклу Стирлинга. Описаны рабочие тела, системы регулирования, испытания и применения двигателей Стирлинга, даны их характеристики....
М.: Машиностроение, 1985. - 408 с.
Сокр. Пер. с англ. Б.В. Сутугина и Н.В. Сутугина (Walker G. Stirling Engines / Clarendon Press, Oxford, 1980.)
В книге изложены теория, расчет и конструирование двигателей различных модификаций, работающих по циклу Стирлинга. Описаны рабочие тела, системы регулирования, испытания и применения двигателей Стирлинга, даны их характеристики....
Пер. с англ.: — М.: Энергия, 1978. — 152 с., ил.
Книга посвящена новому перспективному типу тепловых машины — двигателям Стирлинга, находящим применение в энергетических и холодильных установках, тепловых насосах, а также различных транспортных и технологических устройствах. Дан термодинамический анализ цикла Стирлинга. Рассмотрены варианты конструктивного выполнения двигателей...
Пер. с англ.: — М.: Энергия, 1978. — 152 с., ил. Книга посвящена новому перспективному типу тепловых машины — двигателям Стирлинга, находящим применение в энергетических и холодильных установках, тепловых насосах, а также различных транспортных и технологических устройствах. Дан термодинамический анализ цикла Стирлинга. Рассмотрены варианты конструктивного выполнения двигателей...
Комментарии